| Both sides previous revisionPrevious revisionNext revision | Previous revision |
| en:hardware:arm-can:setup [2010/05/27 14:54] – mikk.leini | en:hardware:arm-can:setup [2020/07/20 09:00] (current) – external edit 127.0.0.1 |
|---|
| ====== Kit setup ====== | ====== Kit Setup ====== |
| |
| ===== Connecting modules ===== | ===== Connecting Modules ===== |
| |
| {{:images:hardware:arm-can:connecting:controller_programmer.jpg?400|}} | [{{ :images:hardware:arm-can:connecting:controller_programmer.jpg?250|Connecting Programmer to Controller}}] |
| {{:images:hardware:arm-can:connecting:controller_userinterface.jpg?400|}} | |
| |
| - **Install Keil uVision Evaluation version** \\ Located in Software/mdk410.exe | To use the programmer connect it as shown in the picture. Currently there are two versions of programmers - one which plugs right on top of controller boar, and another one with 20-pin ribbon cable. Both of these versions have a USB receptable on the right side. |
| - **Install StellarisWare** \\ Located in Software/SW-LM3S-5570.exe \\ It is necessary to install it to the "C:\StellarisWare" folder otherwise example project files should be re-configured. | |
| - **Copy examples to your computer** \\ Copy Examples folder to any place in your harddrive. Please note that after modifing project files uVision saves file paths as absolute so moving the folder later can cause trouble. | [{{ :images:hardware:arm-can:connecting:controller_userinterface.jpg?250|Connecting User-interface to Controller}}] |
| - **Connect the programmer to your computer** \\ Stellaris Evalution Board clone should be found. Install the device drivers located in Software/Luminary_FTDI_Driver folder. | |
| - **Connect the programmer with 20 wire ribbon cable to target board and power the board either through the USB port or external 5V power supply** | The connection of the user-interface is done through a COMM connector with ribbon cable as shown in the picture. |
| - **Try any example project file (.uvproj extension) with Keil uVision** \\ You can use uVision to compile and download project code to ARM device. Please note that uVision does not reset the device after programming so it is required to press the reset button (left one) on board after downloading the code. | |
| | ~~CL~~ |
| | |
| | ===== Installing Software ===== |
| | |
| | - **Install Keil uVision Evaluation version** \\ It is named //Software/mdk410.exe// on CD. The same evaluation version is available on the [[http://www.keil.com/uvision|uVision homepage]]. |
| | - **Install StellarisWare** \\ It's path on CD is //Software/SW-LM3S-5570.exe//. It can also be downloaded from Texas Instruments Stellaris [[http://www.luminarymicro.com/products/software.html|web page]]. It is necessary to install the software to the "C:\StellarisWare" folder otherwise example project files should be re-configured. |
| | - **Copy examples to your computer** \\ Copy Examples folder from CD or from web-page to any place in your harddrive. Please note that after modifing project files, uVision saves file paths as absolute so moving the folder later can cause trouble. |
| | - **Connect the programmer to your computer** \\ Stellaris Evalution Board clone should be found. Install the device drivers located in //Software/Luminary_FTDI_Driver// folder on CD or download them from the same site as StellarisWare. |
| | |
| | ===== Run test ===== |
| | |
| | [{{:images:hardware:arm-can:install:uvision_demo_project.png|RGB LED demo project opened with Keil uVision}}] |
| | ~~CL~~ |
| | |
| | Try any of the example projects with Keil uVision. For example, locate "rgb_led_demo" project and open "rgb_led_demo.uvproj" file. You can use uVision to compile and download project code to an ARM device - there are quickbuttons on the left side of the toolbar for this. Please note that uVision does not reset the device after programming so it is required to press the reset button on the Controller board (the left one) after downloading the code. |
