Differences

This shows you the differences between two versions of the page.

--- en:hardware:arm-can:controller [2010/05/27 12:42] – mikk.leini
+++ en:hardware:arm-can:controller [2020/07/20 09:00] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
 ====== Controller ======
+[{{  :images:hardware:arm-can:modules:controller_enclosure.jpg?250|Controller module}}]
+/*
 [{{  :images:hardware:arm-can:main_board_1.jpg?250|Board front view}}]
 [{{  :images:hardware:arm-can:main_board_2.jpg?250|Board back view}}]
+*/
 ===== Features =====
@@ Line 23: / Line 26: @@
   * 1 x USB device / host (Micro-AB)
-Every pin has IO functionality (except PWM)
+Every pin has I/O functionality (except PWM)
 ADC and PWM have 3 pin headers with ground and +5 V
@@ Line 48: / Line 51: @@
 [{{  :images:hardware:arm-can:connectors:controller_connectors.png|ARM-CAN connectors}}]
-The following chapters describe each of the connectors on ARM-CAN controller module. To recognize the connectors the controller has to be held like shown on the picture.
+The following chapters describe each of the connectors on ARM-CAN Controller module. To recognize the connectors the Controller has to be held as shown on the picture.
 ~~CL~~
@@ Line 66: / Line 69: @@
 [{{  :images:hardware:arm-can:connectors:controller_adc2.png|ADC2 connector}}]
-Both ADC1 and ADC2 connector have two RC-servo like pinouts. There are ground, supply and input-output pins. It is easy to connect simple sensors like potentiometer, thermistor, IR distance sensor and ultrasonic distance sensor to these pins. IO pins can be used as +5 V compatible inputs or outputs with +3,3 V high level. These connectors can also be used to control RC-servos with software PWM when the servo accepts 3,3 V signal.
+Both ADC1 and ADC2 connectors have two RC-servo like pinouts. There are ground, supply and input-output pins. It is easy to connect simple sensors like potentiometer, thermistor, IR distance sensor and ultrasonic distance sensor to these pins. I/O pins can be used as +5 V compatible inputs or outputs with +3.3 V high level. These connectors can also be used to control RC-servos with software PWM when the servo accepts 3.3 V signal.
 ~~CL~~
@@ Line 74: / Line 77: @@
 [{{:images:hardware:arm-can:connectors:controller_communication.png|COMM connector}}]
+COMM connector is a combination of UART, SPI and I2C interfaces. Beside the +5 V supply it contains +3.3 V supply which supplies up to 700 mA. COMM connector is intended to connect with ARM-CAN User Interface and that is why it also features 2 ADC and 1 PWM pins, which are used by the joystick and speaker.
+==== JTAG ====
+[{{:images:hardware:arm-can:connectors:controller_jtag.png|JTAG connector}}]
+ARM-CAN Controller board has a standard 20-pin JTAG connector with essential pins for programming and debugging. Although the kit contains ARM-CAN programmer, other standard ARM debuggers can be used.
+==== CAN ====
+[{{  :images:hardware:arm-can:connectors:controller_can.png|CAN connector(s)}}]
+ARM-CAN Controller board contains two identical CAN 10-pin header connectors. Both of the connectors are on the same bus, therefore CAN network can be formed by daisy-chaining several Controllers. There is no CAN signal terminator on the Controller board so external terminators should be used.
+Microcontroller CAN RX and TX pins which connect to the on-board CAN translator are marked with orange color on the image.
 ~~CL~~
-==== JTAG ====
+==== USB ====
-[{{:images:hardware:arm-can:connectors:controller_jtag.png|JTAG connector}}]
-[{{:images:hardware:arm-can:connectors:controller_can.png|CAN connector(s)}}]
-[{{:images:hardware:arm-can:connectors:controller_rgb.png|RGB LED pins}}]
-[{{:images:hardware:arm-can:connectors:controller_btn.png|BTN pin}}]
 [{{:images:hardware:arm-can:connectors:controller_usb.png|USB pins}}]
+~~CL~~
+The controller board incorporates the USB micro-AB connector on the right side. Although micro-AB is intended for OTG applications the same connector can be used for device-only and host-only applications. USB inteface has ESD protection on bus and 750 mA fuse on supply line. USB power supply is bi-directional. When  the controller acts as a USB device, current from the USB bus to controller board flows through a Schottky diode, when the controller is used as a host, external power switch to USB bus can be opened with USB_EPEN high signal.
+~~CL~~
+==== RGB LED ====
+[{{  :images:hardware:arm-can:connectors:controller_rgb.png|RGB LED pins}}]
+In the middle of the controller board there is a 350 mW RGB LED. Each of the three colors are driven by separate signal. Green LED has a pull-up resistor which lights up green led by default. It can be turned off when microcontroller pin is configured as output with low signal.
+~~CL~~
+==== Buttons ====
+[{{  :images:hardware:arm-can:connectors:controller_btn.png|BTN pin}}]
+There are two buttons on board. The left one resets microcontroller when pressed; the right one is used as a custom button for user application. The button has an RC filter which filters button bounces.
+~~CL~~
+/*
 ===== Schematics =====
   * {{:datasheets:arm-can:controller.pdf|Schematics}}
+*/

en/hardware/arm-can/controller.1274964165.txt.gz · Last modified: 2020/07/20 09:00 (external edit)