Hello !
?
Trace: • Timer

Table of Contents

Timer

Diese Bibliothek deckt einen großen Teil der Funktionen des Timers des ATmega128 ab. Es gibt Datentypen und Funktionen welche das Benutzen von Timern vereinfachen. Aufgrund der Komplexität der AVR Timer gibt es leider keine allgemeingültige Funktion, die für verschiedene Timer genutzt werden kann. Die Funktionen jedes Timers beginnen mit dem Präfix “timer” und seinem Index.

Datentypen

  • timer0_prescale
    Timer 0 Vorteiler, Aufzählungsdatentyp. Möglichkeiten:
    • TIMER0_NO_PRESCALE - Kein Vorteiler (keine Division).
    • TIMER0_PRESCALE_8 - Clk / 8.
    • TIMER0_PRESCALE_32 - Clk / 32.
    • TIMER0_PRESCALE_64 - Clk / 64.
    • TIMER0_PRESCALE_128 - Clk / 128.
    • TIMER0_PRESCALE_256 - Clk / 256.
    • TIMER0_PRESCALE_1024 - Clk / 1024.
  • timer2_prescale
    Timer 2 Vorteiler, Aufzählungsdatentyp. Möglichkeiten:
    • TIMER2_NO_PRESCALE - kein Vorteiler (keine Division).
    • TIMER2_PRESCALE_8 - Clk / 8.
    • TIMER2_PRESCALE_64 - Clk / 64.
    • TIMER2_PRESCALE_256 - Clk / 256.
    • TIMER2_PRESCALE_1024 - Clk / 1024.
    • TIMER2_PRESCALE_T2_FALLING - Taktgeber an Pin T2 fallende Flanke.
    • TIMER2_PRESCALE_T2_RISING - Taktgeber an Pin T2 steigende Flanke.
  • timer1_prescale
  • timer3_prescale
    Timer 1/3 Vorteiler, Aufzählungsdatentyp. Möglicheiten (“n” bedeutet 1 oder 3):
    • TIMERn_NO_PRESCALE - Kein Vorteiler (keine Division).
    • TIMERn_PRESCALE_8 - Clk / 8.
    • TIMERn_PRESCALE_64 - Clk / 64.
    • TIMERn_PRESCALE_256 - Clk / 256.
    • TIMERn_PRESCALE_1024 - Clk / 1024.
    • TIMERn_PRESCALE_Tn_FALLING - Taktgeber an Pin Tn fallende Flanke.
    • TIMERn_PRESCALE_Tn_RISING - Taktgeber an Pin Tn steigende Flanke.
  • timer1_ctc_top
  • timer3_ctc_top
    Timer 1/3 CTC Modus, Höchstwert, Aufzählungsdatentyp. Möglichkeiten (“n” bedeutet 1 oder 3):
    • TIMERn_CTC_TOP_OCRA - Höchstwert des Timers 1/3 output compare register A.
    • TIMERn_CTC_TOP_ICR - Höchstwert des Timers 1/3 input capture register.
  • timer1_fast_pwm_top
  • timer3_fast_pwm_top
    Timer 1/3 fast PWM mode top value enumeration data type. Options (“n” means 1 or 3):
    • TIMERn_FAST_PWM_TOP_256 - Höchstwert 255.
    • TIMERn_FAST_PWM_TOP_512 - Höchstwert 511.
    • TIMERn_FAST_PWM_TOP_1024 - Höchstwert 1023.
    • TIMERn_FAST_PWM_TOP_ICR - Höchstwert des Timers 1/3 input capture register.
    • TIMERn_PAST_PWM_TOP_OCRA - Höchstwert des Timers 1/3 output compare register A.
  • timer1_fast_pwm_output_mode
  • timer3_fast_pwm_output_mode
    Timer 1/3 fast PWM mode outputs configuration enumeration data type. Options (“n” means 1 or 3):
    • TIMERn_FAST_PWM_OUTPUT_DISABLE - No output.
    • TIMERn_FAST_PWM_OUTPUT_TOGGLE_ON_MATCH - Output toggles on compare match.
    • TIMERn_FAST_PWM_OUTPUT_CLEAR_ON_MATCH - Output clears on compare match.
    • TIMERn_FAST_PWM_OUTPUT_SET_ON_MATCH - Output sets on compare match.

Funktionen

  • void timer0_init_normal(timer0_prescale prescale)

Initialisiert Timer 0 im normalen Modus. In diesem Modus zählt der Timer von 0 bis 255 (inkl.). Overflowinterrupts können genutzt werden. Parameter.

  • prescale - Prescaler.
  • void timer2_init_normal(timer2_prescale prescale)

Initialisiert Timer 2 im normalen Modus. In diesem Modus zählt der Timer von 0 bis 255 (inkl.). Overflowinterrupts können genutzt werden. Parameter.

  • prescale - Prescaler.
  • void timer0_stop()
  • void timer2_stop()

Stoppt Timer 0/2.

  • unsigned char timer0_get_value(void)
  • unsigned char timer2_get_value(void)

Returns timer 0/2 current value. Parameters:

  • Return 8-bit timer value.
  • void timer0_set_value(unsigned char value)
  • void timer2_set_value(unsigned char value)

Sets timer 0/2 value. Parameters:

  • value - New 8-bit timer value.
  • void timer0_overflow_interrupt_enable(bool enable)
  • void timer2_overflow_interrupt_enable(bool enable)

Enables or disables timer 0/2 overflow interrupt. The name of the interrupt vector is “TIMERn_OVF_vect” where “n” represents 0 or 2. Parameters:

  • enable - true to enable interrupt, false to disable.
  • bool timer0_overflow_flag_is_set(void)
  • bool timer2_overflow_flag_is_set(void)

Checks timer 0/2 overflow flag. Parameters:

  • Returns true when overflow has happened, false when not.
  • void timer0_overflow_flag_clear(void)
  • void timer2_overflow_flag_clear(void)

Resets timer 0/2 overflow flag.

  • void timer1_init_normal(timer1_prescale prescale)
  • void timer3_init_normal(timer3_prescale prescale)

Initializes timer 1/3 in normal mode. In this mode timer counts from 0 to 65535 (including). Overflow interrupt can be used. Parameters:

  • prescale - Prescaler.
  • void timer1_init_ctc(timer1_prescale prescale, timer1_ctc_top top)
  • void timer3_init_ctc(timer3_prescale prescale, timer3_ctc_top top)

Initializes timer 1/3 in CTC (Clear Timer on Compare Match) mode. In this mode timer counts to specified top value. Overflow interrupt can be used. Parameters:

  • prescale - Prescaler.
  • top - Timer top value selection. Actual value must be specified with register selected as a top value holder.
  • void timer1_init_fast_pwm(timer1_prescale prescale, timer1_fast_pwm_top top, timer1_fast_pwm_output_mode output_a, timer1_fast_pwm_output_mode output_b, timer1_fast_pwm_output_mode output_c)
  • void timer3_init_fast_pwm(timer3_prescale prescale, timer3_fast_pwm_top top, timer3_fast_pwm_output_mode output_a, timer3_fast_pwm_output_mode output_b, timer3_fast_pwm_output_mode output_c)

Initializises timer 1/3 in fast PWM mode. In this mode timer counts to a specified value, which also determines the period of the PWM signal. Timer 1/3 has three 3 output compare units (A, B and C) to generate PWM signals. Overflow and compare match interrupts can be used. Parameters:

  • prescale - Prescaler.
  • top - Timer top value selection. Actual value must be specified with register selected as a top value holder.
  • output_a - Output compare unit A pin configuration.
  • output_b - Output compare unit B pin configuration.
  • output_c - Output compare unit C pin configuration.
  • void timer1_stop()
  • void timer3_stop()

Stops timer 1/3.

  • unsigned char timer1_get_value(void)
  • unsigned char timer3_get_value(void)

Returns timer 1/3 current value. Parameters:

  • Returns 16-bit timer value.
  • void timer1_set_value(unsigned char value)
  • void timer3_set_value(unsigned char value)

Sets timer 0/2 value. Parameters:

  • value - New 16-bit timer value.
  • unsigned short timer1_get_compare_match_unitA_value(void)
  • unsigned short timer1_get_compare_match_unitB_value(void)
  • unsigned short timer1_get_compare_match_unitC_value(void)
  • unsigned short timer3_get_compare_match_unitA_value(void)
  • unsigned short timer3_get_compare_match_unitB_value(void)
  • unsigned short timer3_get_compare_match_unitC_value(void)

Returns timer 1/3 output compare unit A/B/C compare match register value. Parameters:

  • Returns 16-bit compare match register value.
  • void timer1_set_compare_match_unitA_value(unsigned short value)
  • void timer1_set_compare_match_unitB_value(unsigned short value)
  • void timer1_set_compare_match_unitC_value(unsigned short value)
  • void timer3_set_compare_match_unitA_value(unsigned short value)
  • void timer3_set_compare_match_unitB_value(unsigned short value)
  • void timer3_set_compare_match_unitC_value(unsigned short value)

Sets timer 1/3 output compare unit A/B/C compare match register value. Parameters:

  • value - New 16-bit compare match register value.
  • unsigned short timer1_get_input_capture_value(void)
  • unsigned short timer3_get_input_capture_value(void)

Returns timer 1/3 input capture register value. Parameters:

  • Returns 16-bit input capture register value.
  • void timer1_set_input_capture_value(unsigned short value)
  • void timer3_set_input_capture_value(unsigned short value)

Sets timer 1/3 input capture register value. Parameters:

  • value - New 16-bit input capture register value.
  • void timer1_overflow_interrupt_enable(bool enable)
  • void timer3_overflow_interrupt_enable(bool enable)

Enables or disables timer 1/3 overflow interrupt. The name of the interrupt vector is “TIMERn_OVF_vect” where “n” represents 1 või 3. Parameters:

  • enable - true to enable interrupt, false to disable.
  • void timer1_compare_match_unitA_interrupt_enable(bool enable)
  • void timer1_compare_match_unitB_interrupt_enable(bool enable)
  • void timer1_compare_match_unitC_interrupt_enable(bool enable)
  • void timer3_compare_match_unitA_interrupt_enable(bool enable)
  • void timer3_compare_match_unitB_interrupt_enable(bool enable)
  • void timer3_compare_match_unitC_interrupt_enable(bool enable)

Enables or disables timer 1/3 output compare unit A/B/C compare match interrupt. The name of the interrupt vector is “TIMERn_COMPx_vect” where “n” represents 1 or 3 and “x” represents A, B or C. Parameters:

  • enable - true to enable interrupt, false to disable.
  • void timer1_input_capture_interrupt_enable(bool enable)
  • void timer3_input_capture_interrupt_enable(bool enable)

Enables or disables timer 1/3 input capture interrupt. The name of the interrupt vector is “TIMERn_CAPT_vect”, where “n” represents 1 or 3. Parameters:

  • enable - true to enable interrupt, false to disable.
  • bool timer1_overflow_flag_is_set(void)
  • bool timer3_overflow_flag_is_set(void)

Checks timer 1/3 overflow flag. Parameters:

  • Returns true when overflow has happened, false when not.
  • bool timer1_input_capture_flag_is_set(void)
  • bool timer3_input_capture_flag_is_set(void)

Checks timer 1/3 input capture flag. Parameters:

  • Returns true when input capture has done, false when not.
  • void timer1_overflow_flag_clear(void)
  • void timer3_overflow_flag_clear(void)

Resets timer 1/3 overflow flag.

  • void timer1_input_capture_flag_clear(void)
  • void timer3_input_capture_flag_clear(void)

Resets timer 1/3 input capture flag.

Beispiel

Im folgenden Programm wird Timer 0 im normalen Modus mit Overflowinterrupt gestartet. 

#include <homelab/timer.h>
#include <avr/interrupt.h>
 
// Overflow interrupt program.
ISR(TIMER0_OVF_vect)
{
}
 
int main(void)
{	
	// Initializing of timer 0 in normal mode.
	timer0_init_normal(TIMER0_PRESCALE_32);
 
	// Enabling timer 0 overflow interrupt.
	timer0_overflow_interrupt_enable(true);
 
	// Global interrupts enabling.
	sei();
}
de/software/homelab/library/timer.txt · Last modified: 2020/07/20 09:00 by 127.0.0.1
CC Attribution-Share Alike 4.0 International
www.chimeric.de Valid CSS Driven by DokuWiki do yourself a favour and use a real browser - get firefox!! Recent changes RSS feed Valid XHTML 1.0